Gw-instek LCR-800 Series Manuel d'utilisateur Page 5
- Page / 72
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SAFETY INSTRUCTIONS
9
Power cord for the United Kingdom
When using the LCR-800 in the United Kingdom, make sure the
power cord meets the following safety instructions.
NOTE: This lead/appliance must only be wired by competent persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with the
following code:
Green/ Yellow: Earth
Blue: Neutral
Brown: Live (Phase)
As the colours of the wires in main leads may not correspond with the colours
marking identified in your plug/appliance, proceed as follows:
The wire which is coloured Green & Yellow must be connected to the Earth
terminal marked with the letter E or by the earth symbol
or coloured Green or
Green & Yellow.
The wire which is coloured Blue must be connected to the terminal which is
marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the terminal marked
with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment or contact the
supplier.
This cable/appliance should be protected by a suitably rated and approved HBC
mains fuse: refer to the rating information on the equipment and/or user
instructions for details. As a guide, cable of 0.75mm2 should be protected by a
3A or 5A fuse. Larger conductors would normally require 13A types, depending
on the connection method used.
Any moulded mains connector that requires removal /replacement must be
destroyed by removal of any fuse & fuse carrier and disposed of immediately, as
a plug with bared wires is hazardous if a engaged in live socket. Any re-wiring
must be carried out in accordance with the information detailed on this label.
LCR-800 User Manual
10
GETTING STARTED
This chapter describes the instrument’s main
features, front & rear panels, power up sequence,
fixture connections and calibration.
Main Features
Main Features .............................................................. 11
Model comparison ...................................................... 12
Measurement type
Measurement item ...................................................... 12
Measurement combination ......................................... 12
Panel overview
Front Panel Overview .................................................. 13
Rear Panel Overview .................................................... 16
Setup
Power Up ..................................................................... 18
Tilt stand ...................................................................... 18
Power up ...................................................................... 18
Fixture connection
Fixture Connection ...................................................... 20
Fixture structure .......................................................... 20
Fixture connection ....................................................... 21
Bias voltage
connection
External voltage bias connection ................................ 22
Zeroing
Zeroing ......................................................................... 24
Zeroing calibration ...................................................... 24
- Precision LCR Meter 1
- Table of Contents 2
- SAFETY INSTRUCTIONS 3
- GETTING STARTED 5
- Main Features 6
- Measurement Types 6
- Front Panel Overview 7
- Rear Panel Overview 8
- Power Up 9
- Fixture Connection 10
- Fixture connection 11
- Zeroing 12
- BASIC MEASUREMENT 15
- Parameter Configuration 16
- Measurement Modes 17
- Set Bias voltage 17
- Set measurement frequency 18
- Set measurement voltage 19
- Set PPM for D/Q measurements 19
- Set constant voltage source 20
- Set Range hold 20
- Set Average 20
- Set Nominal Values 21
- Running Measurement 22
- Store Recall 23
- BIN FUNCTIONS 24
- Binning Menu 25
- Handler Menu 26
- Mode Setting 26
- Circuit Setting 27
- Speed Setting 27
- Display Setting 27
- Frequency Setting 27
- Select/Run Auto/Manu Sorting 28
- Voltage Setting 28
- Bias Setting 29
- Range Setting 29
- Constant Voltage Setting 29
- Delay Setting 30
- Average Setting 30
- Set Bin Menu 31
- + : 4.02% 32
- Ω- : 4.02% 32
- Set Max/Min Absolute Limit 33
- Set Max/Min Percentage Limit 33
- Bin Summary Menu 34
- Bin Summary/Results 35
- RS232 REMOTE 36
- LCR Setup 37
- LCR Viewer 37
- LCR Viewer File Settings 39
- View Data 41
- View Help 41
- Terminal Connection 42
- PROGRAMMING 44
- Commands 45
- DISPLAY 46
- CIRCUIT 47
- FREQUENCY 47
- VOLTAGE 47
- AUTO/MANU 48
- RANGE HOLD 48
- NOM.VAL 50
- AVERAGE 52
- RECALL CALIBRATION 52
- BAUD RATE 52
- MODEL NUMBER 52
- ON-LINE 53
- MEASURE HOLD 53
- MEASURE RECOVER 53
- LEVEL DISPLAY 53
- PRIMARY FACTOR 53
- PRIMARY OV01 54
- PRIMARY OVER SECONDARY OVER 54
- INTERACE 56
- Signal Overview 58
- Handler Timing 60
- APPENDIX 62
- Series Resistance R 63
- Parallel Resistance R 63
- DC Resistance R 63
- Parallel Conductance 63
- Capacitance (C) Formula 64
- Inductance (L) Formula 64
- Accuracy Definitions 66
- Specifications 68
- EC Declaration of Conformity 70
- INDEX 71
- LCR-800 User Manual 71
Produits connexes et manuels pour Équipement Gw-instek LCR-800 Series
(14 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.849 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels