Gw-instek APS-1102 User Manual Manuel d'utilisateur Page 221
- Page / 265
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6.6 Error Message List
APS-1102 Programmable AC/DC Power Source 6-49
6.6 Error Message List
USB error messages are listed in Table 6-15 below.
Table 6-15. USB Error Message List
No. Message Cause
0 “No error” No error.
100 “Command error”
Command was recognized as invalid due to any cause.
(General command error)
101 “Invalid character”
Command was recognized as invalid due to invalid characters
(such as “VOLT&”) in command string.
102 “Syntax error”
Command was recognized as invalid due to reception of
undefined command or parameter.
200 “Execution error”
Error occurred when executing the command due to any cause.
(General execution error)
222 “Data out of range”
Error occurred when executing the command due to out of range
parameter.
350 “Too Many Errors” New errors cannot be retained due to error queue overflow.
1 “Invalid with output on”
Error occurred when executing the command because the output
relay was on.
2 “Invalid with output off”
Error occurred when executing the command because the output
relay was off.
3 “Invalid in this mode”
Error occurred when executing the command due to inappropriate
output mode.
4 “Under Busy State” Error occurred during execution of command due to busy device.
5 “Out of Limiter”
Error occurred during execution of command because limiter
value was exceeded.
6 “Invalid in this frequency”
Error occurred when executing the command due to inappropriate
oscillation frequency setting.
7
“Out of Input Signal
frequency”
Error occurred when executing the command due to out of the
external synchronization frequency range.
8 “Under Warning State”
Error occurred when executing the command because device was
operating in protected mode.
- APS-1102 1
- USER MANUAL 1
- Preface 3
- Safety Precautions 4
- Contents 6
- Figures 10
- OVERVIEW 15
- 1.1 General 16
- 1.2 Features 16
- 1.3 Applications 17
- 1.4 List of Functions 18
- 1.5 Operation Principles 20
- PREPARATIONS BEFORE USE 21
- 2.1 Checking Before Use 22
- Installation sites 23
- Cautions for transport 23
- WARNING 25
- 2.4 Simple Operation Checks 28
- 2.5 Calibration 30
- PANEL AND BASIC OPERATIONS 31
- 3.1.1 Operation panel 32
- 3.1.2 Front panel 33
- 3.1.3 Rear panel 34
- Display at power-on 35
- Initial settings 35
- At Power-on 36
- 3.3 I/O Terminals 37
- 3.3.2 USB connector 40
- 3.3.3 External control I/O 41
- External signal input/ 43
- 3.4 Main Operation Example 44
- 3.4.1 Power on/off 45
- Output on 46
- Output off 46
- 3.4.2 Setting output mode 47
- Status window 50
- 3.4.4 Setting waveform 51
- Modification box 58
- Output on/off LED on 59
- 3.5 Output Characteristics 63
- Maximum output power = 750 W 64
- ADVANCED OPERATION EXAMPLE 65
- Selection box 68
- 4.2.1 Inrush current 78
- EXEC box 82
- 4.4.1 Sequence operations 85
- phase 91
- 4.4.2 Sequence settings 92
- Operation step <1> 97
- IncreaseDecrease 98
- Operation step <2> 99
- Operation steps 100
- Operation step 101
- Setting step 1 104
- Selection box 105
- Setting step 2 106
- STOPSTART 107
- LOCALHOLD 107
- SEQUENCE 107
- Output on/off LED is on 108
- Step number being executed 110
- ENTERCANCEL 113
- Output waveform example 114
- External sync signal (TTL) 114
- 4.8 Using Memory Functions 117
- Indication on Control Panel 118
- CAUTION 121
- Increase 123
- Decrease 123
- 5. MENUS 127
- 5.1 Screen Configuration 129
- 5.1.1 Status icons 131
- 5.1.3 Sequence display 132
- 5.2.1 Menus 133
- 5.2.5 EXEC input 140
- 5.2.6 Shortcut keys 140
- 5.3 SET Menu 141
- 5.3.1 Output mode setting 142
- 5.3.6 Waveform settings 145
- 5.4 MEASURE Screen 148
- 5.5 MISC Menu 153
- 5.5.2 Memory (MEMORY) 157
- 5.6 System Menu 162
- USB INTERFACE 173
- 6.1 Setup for Use 174
- 6.2 Command List 175
- 6.3 Command Descriptions 181
- Non-zero 182
- Numerals 182
- 8-bit data byte 182
- Root level 183
- Current path 183
- :SOUR:FREQ 1000 184
- [SOURce:]MODE 189
- [SOURce:]PHASe:CLOCk 189
- [SOURce:]SEQuence:CSTep? 190
- [SOURce:]SEQuence:LEN? 190
- [SOURce:]SEQuence:COUNt? 191
- [SOURce:]SEQuence:DELete 191
- [SOURce:]SEQuence:STEP 194
- [SOURce:]VOLTage:RANGe 195
- STATus:OPERation:ENABle 202
- STATus:OPERation[:EVENt]? 202
- STATus:WARNing:CONDition? 203
- STATus:WARNing:ENABle 204
- STATus:WARNing[:EVENt]? 204
- OUTPut[:STATe] 205
- INPut:GAIN 205
- TRACe:CATalog? 206
- TRACe[:DATA] 206
- TRACe:DELete[:NAME] 207
- SYSTem:BEEPer:STATe 207
- SYSTem:CONFigure:EXTIO 207
- SYSTem:ERRor? 208
- SYSTem:PON[:OUTPut] 208
- SYSTem:TUNit 208
- SYSTem:WRELease 209
- CLS 210
- ESE 210
- ESR? 210
- IDN? 211
- OPC 211
- RCL 211
- RST 212
- SRE 212
- STB? 212
- TST? 213
- WAI 213
- CONFigure 214
- 6.5.1 Status byte 216
- 6.5.3 Operation status 219
- 6.5.4 Warning status 220
- 6.6 Error Message List 221
- 6.7 Programming Precautions 222
- TROUBLESHOOTING 223
- 7.1 Protection Function 224
- 7.2.1 Error at power-on 227
- Message box 230
- 7.2.4 Warning messages 232
- 7.3 When Fault Is Suspected 235
- LCD contrast adjustment” 236
- Keylock” 236
- MEASURE 239
- MAINTENANCE 241
- 8.1 Introduction 242
- 8.2 Routine Maintenance 242
- 8.5 Backup Battery 247
- SPECIFICATIONS 249
- 9.1 Output 250
- Output terminals 251
- Rated output 251
- Output voltage settings 251
- Maximum output current 251
- Line regulation 253
- Output DC offset 253
- 9.2 Current Limiter 254
- 9.3 Setting Range Limits 254
- 9.4 Signal Sources 255
- 9.5 Measurement Functions 256
- Output power measurement 257
- 9.6 Sequence Function 258
- 9.8 Setting Memory 259
- 9.9 Protection Functions 259
- 9.10 General 260
- 9.11 External Control I/O 261
- 9.12 USB Interface 261
- 9.13 Power Input 261
- Withstand voltage 262
- Insulation resistance 262
- Safety 262
- EMC Compliance 262
- External dimensions 263
- Weight 263
- ◎ Safety 265
Produits connexes et manuels pour Équipement Gw-instek APS-1102 User Manual
(268 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.209 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels