Gw-instek APS-1102 User Manual Manuel d'utilisateur Page 47
- Page / 265
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3.4 Main Operation Example
APS-1102 Programmable AC/DC Power Source 3-17
3.4.2 Setting output mode
The APS-1102 provides the eight output modes listed in Table 3-4. The output mode cannot be changed
while output is on. Before changing the output mode, set output to off.
Table 3-4. Output Mode List
Operation
Mode
Signal Source Mode Output Mode Reference
AC
INT
(internal)
AC-INT
“3.4.2 Setting output mode”
EXT
(external)
AC-EXT
“4.5 Control Using External Control I/O
Connector
”
ADD
(internal + external)
AC-ADD
“4.10 Adding External Signals and
Internal Signals
SYNC
(external sync)
AC-SYNC
“4.7 Synchronization of Output to
External Signal
”
AC+DC
INT
(internal)
AC+DC-INT
“4.1 Use as a DC Power Source”
EXT
(external)
AC+DC-EXT
“4.5 Control Using External Control I/O
Connector
”
ADD
(internal + external)
AC+DC-ADD
“4.10 Adding External Signals and
Internal Signals
SYNC
(external sync)
AC+DC-SYNC
“4.7 Synchronization of Output to
External Signal”
Setting to AC-INT mode is described below as an example.
- APS-1102 1
- USER MANUAL 1
- Preface 3
- Safety Precautions 4
- Contents 6
- Figures 10
- OVERVIEW 15
- 1.1 General 16
- 1.2 Features 16
- 1.3 Applications 17
- 1.4 List of Functions 18
- 1.5 Operation Principles 20
- PREPARATIONS BEFORE USE 21
- 2.1 Checking Before Use 22
- Installation sites 23
- Cautions for transport 23
- WARNING 25
- 2.4 Simple Operation Checks 28
- 2.5 Calibration 30
- PANEL AND BASIC OPERATIONS 31
- 3.1.1 Operation panel 32
- 3.1.2 Front panel 33
- 3.1.3 Rear panel 34
- Display at power-on 35
- Initial settings 35
- At Power-on 36
- 3.3 I/O Terminals 37
- 3.3.2 USB connector 40
- 3.3.3 External control I/O 41
- External signal input/ 43
- 3.4 Main Operation Example 44
- 3.4.1 Power on/off 45
- Output on 46
- Output off 46
- 3.4.2 Setting output mode 47
- Status window 50
- 3.4.4 Setting waveform 51
- Modification box 58
- Output on/off LED on 59
- 3.5 Output Characteristics 63
- Maximum output power = 750 W 64
- ADVANCED OPERATION EXAMPLE 65
- Selection box 68
- 4.2.1 Inrush current 78
- EXEC box 82
- 4.4.1 Sequence operations 85
- phase 91
- 4.4.2 Sequence settings 92
- Operation step <1> 97
- IncreaseDecrease 98
- Operation step <2> 99
- Operation steps 100
- Operation step 101
- Setting step 1 104
- Selection box 105
- Setting step 2 106
- STOPSTART 107
- LOCALHOLD 107
- SEQUENCE 107
- Output on/off LED is on 108
- Step number being executed 110
- ENTERCANCEL 113
- Output waveform example 114
- External sync signal (TTL) 114
- 4.8 Using Memory Functions 117
- Indication on Control Panel 118
- CAUTION 121
- Increase 123
- Decrease 123
- 5. MENUS 127
- 5.1 Screen Configuration 129
- 5.1.1 Status icons 131
- 5.1.3 Sequence display 132
- 5.2.1 Menus 133
- 5.2.5 EXEC input 140
- 5.2.6 Shortcut keys 140
- 5.3 SET Menu 141
- 5.3.1 Output mode setting 142
- 5.3.6 Waveform settings 145
- 5.4 MEASURE Screen 148
- 5.5 MISC Menu 153
- 5.5.2 Memory (MEMORY) 157
- 5.6 System Menu 162
- USB INTERFACE 173
- 6.1 Setup for Use 174
- 6.2 Command List 175
- 6.3 Command Descriptions 181
- Non-zero 182
- Numerals 182
- 8-bit data byte 182
- Root level 183
- Current path 183
- :SOUR:FREQ 1000 184
- [SOURce:]MODE 189
- [SOURce:]PHASe:CLOCk 189
- [SOURce:]SEQuence:CSTep? 190
- [SOURce:]SEQuence:LEN? 190
- [SOURce:]SEQuence:COUNt? 191
- [SOURce:]SEQuence:DELete 191
- [SOURce:]SEQuence:STEP 194
- [SOURce:]VOLTage:RANGe 195
- STATus:OPERation:ENABle 202
- STATus:OPERation[:EVENt]? 202
- STATus:WARNing:CONDition? 203
- STATus:WARNing:ENABle 204
- STATus:WARNing[:EVENt]? 204
- OUTPut[:STATe] 205
- INPut:GAIN 205
- TRACe:CATalog? 206
- TRACe[:DATA] 206
- TRACe:DELete[:NAME] 207
- SYSTem:BEEPer:STATe 207
- SYSTem:CONFigure:EXTIO 207
- SYSTem:ERRor? 208
- SYSTem:PON[:OUTPut] 208
- SYSTem:TUNit 208
- SYSTem:WRELease 209
- CLS 210
- ESE 210
- ESR? 210
- IDN? 211
- OPC 211
- RCL 211
- RST 212
- SRE 212
- STB? 212
- TST? 213
- WAI 213
- CONFigure 214
- 6.5.1 Status byte 216
- 6.5.3 Operation status 219
- 6.5.4 Warning status 220
- 6.6 Error Message List 221
- 6.7 Programming Precautions 222
- TROUBLESHOOTING 223
- 7.1 Protection Function 224
- 7.2.1 Error at power-on 227
- Message box 230
- 7.2.4 Warning messages 232
- 7.3 When Fault Is Suspected 235
- LCD contrast adjustment” 236
- Keylock” 236
- MEASURE 239
- MAINTENANCE 241
- 8.1 Introduction 242
- 8.2 Routine Maintenance 242
- 8.5 Backup Battery 247
- SPECIFICATIONS 249
- 9.1 Output 250
- Output terminals 251
- Rated output 251
- Output voltage settings 251
- Maximum output current 251
- Line regulation 253
- Output DC offset 253
- 9.2 Current Limiter 254
- 9.3 Setting Range Limits 254
- 9.4 Signal Sources 255
- 9.5 Measurement Functions 256
- Output power measurement 257
- 9.6 Sequence Function 258
- 9.8 Setting Memory 259
- 9.9 Protection Functions 259
- 9.10 General 260
- 9.11 External Control I/O 261
- 9.12 USB Interface 261
- 9.13 Power Input 261
- Withstand voltage 262
- Insulation resistance 262
- Safety 262
- EMC Compliance 262
- External dimensions 263
- Weight 263
- ◎ Safety 265
Produits connexes et manuels pour Équipement Gw-instek APS-1102 User Manual
(268 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.292 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels